Search filter

Applications: Self-levelling compounds (9); Substrate preparation/Primers (1)
Brands: Bostik (1); Roxol
Destinations: ~~Floors~~ (10)
Specific characteristics: Exterior (1); Ready-to-use (1)
Substrates: ~~Ceramic tiles~~ (10)
Segments: ~~Construction~~ (10)

ROXOL RENO QUICK

Fast-setting rapid repair mortar for smoothing floors and walls.

Additional Downloads
MSDS
1. Subfloor Preparation Guide (55 Kb)
2. Primers and self-levelling compounds (1642 Kb)
Definitions
ImperviousCharacterisitc of a subfloor which porosity is very low. Adhesion on such substrates is usually more difficult and requires more attention and preparation.
PrimerLiquid or paste applied onto a substrate to obtain optimum bonding. It helps regulate the porosity of the substrate (reduce absorption, therefore adhesive usage), increase adhesion to non porous surfaces, improves application properties of later on applied adhesive
Tiling
Working timeTime between end of waiting time and moment when the application is no longer possible

Uses

ROXOL RENO QUICK Rapid Repair Mortar is suitable for smoothing and levelling of screeds, concrete floors up to a maximum thickness of 50 mm in single work step.
For thickness higher than 50 mm, blend with 0.4 to 0.9 mm sharp sand.

Can be used for smoothing walls up to 5 mm thickness.

ROXOL RENO QUICK may be used for local repairs at thickness greater than 30 mm, e.g. filling holes, depressions and cracks; repairing stairs and landings, building up sloping surfaces.

It is recommended for heavy wear and suitable for normal wear. Suitable under parquet, carpeting, PVC coverings, linoleum and tiling.

Not to be used as a wearing surface.

For interior use only.

Benefits

Fast setting
Fine grained
High filling capacity
Vertical and horizontal application
Can be blended with 0.4-0.9 mm grain sand
From feather edge to 50 mm
Suitable for underfloor heating

Properties

Physical:

Composition: Synthetic resin modified cement powder, low in chromate
Colour: Grey
Working temperature : Preferably between +8°C and +25°C. Not below +5°C or above +30°C
Mixing ratio: 5-6 litres of water per 25 kg bag
Working time/Flow life: 15-20 minutes
Set for walking: after 45 min to 1 hour
Dry for floor covering: after approx. 3-5 hours depending on thickness
Resistant to castor wheels: at 1 mm or above
Compressive strength: After: 28 days = 32 MPa
Suitable for underfloor heating: Yes

Consumption:

1.6 to 2 kg/m² per 1 mm thickness

Safety:

IMPORTANT: before embarking on any work involving ROXOL RENO QUICK the separate Product Safety Data Sheet must be studied carefully by those carrying out the work. Do not breath dust, PREVENT skin and eye contact with powder and particularly the wet material when mixed. Strong alkali when wet – can cause serious eye damage and may cause an allergic reaction resulting in skin disorders.

Shelf life:

Up to 6 months in the original unopened bag stored between +10°C and +30°C.

Application

PREPARATION

Subfloors must be sound, of adequate tensile and compressive strength; free from laitance, cracks and structural defects; clean and free from dust, grease, curing compounds, sealers or any other contaminants that would inhibit proper bond.

Substrate residual moisture content must be less than 3%.

For anhydrite slabs, moisture content should be less than 1% for laying textile coverings and ceramic tiles, 0.5% for laying plastic coverings and parquet floors.

New asphalt screeds should be shot-blasted first.

Adhesive residues that are hard, sound and water-tight should be mechanically cut-back to a minimum. Soft and weak adhesive residues and smoothing underlayments should be completely removed.

Underfloor heating

Do not apply when underfloor heating is in operation. Turn off the heating 48 hours before starting the work.

The following substrates must be pre-treated with suitable Bostik primers and bonding agents:

Substrates	Recommended Primer	Consumption	Remarks
Absorbent concrete and cement screeds	Unidur 10 1:3 water-diluted	100 g per sqm/layer	Water based primer
Normally absorbent concrete and cement screeds	Unidur 10 1:3 water-diluted or Unidur N 1:1 water-diluted	100 g per sqm	Water based primer
Impervious concrete and cement screeds, tiles, terrazzo and other similar dense surfaces, existing semi flexible tiles	Unidur N (pure)	100 g to 150 g per sqm	Water based primer
Particle boards, plywood all qualities included waterproof or fireproof, plasterboards, bituminous adhesive residues, magnesite screeds, mastic asphalt screeds	Impreglue	100 g per sqm	Solvent based product - Flammable
Wooden floors, particle boards, plywood all qualities included waterproof or fireproof, plasterboards, adhesive residues ( bituminous, acrylic, alcohol based ), old floor paints, old industrial flooring (epoxy or PU), mastic asphalt screeds, existing semi-flexible tiles.	Primepox	100 g to 150 g per sqm	Water-based epoxy primer 2 components
Wooden floor, particle boards, plywood with gap filling	Primabois	350 to 600 g per sqm	Water-based cementitious primer
Metal decking	Eponal 336	200 g to 250 g per sqm	Epoxy damp proof primer- 2 components
Concrete, cement screeds, old ceramic tiles with humidity above 3% or with negative pressure from the basement	Eponal 336	400 g to 800 g per sqm	Epoxy damp proof primer- 2 components

PRECAUTION: Before using primer read the primer data sheet carefully and respect our recommendations for ground preparation.
Before proceeding with the subsequent application of the compound, always allow primers to dry in accordance with the technical information. Always allow at least 24 hours drying time for anhydrite screeds.

APPLICATION

Pour approx. 5-6 litres of clean water (water temperature +8° to +20°C) into a clean mixing bucket. Stir the compound powder into water with an electric drill and mixing paddle (<500 rpm) to obtain a lump-free mixture.

After mixing, a maturing time of at least 1 minute is recommended to optimise flow. Remix for 30 seconds.

The compound must be applied to the substrate within the specified working time and smoothed with a stainless steel float. Spread the compound to zero in order to fill the pores, then smooth and spread in a regular manner to the desired thickness.

Unblended compound

Approx. 5-6 litres of water per 25 kg bag

Consumption: approx. 1.6 kg per m²/mm

Blended compound

Approx. 6 litres of water per 25 kg bag

+ 5-8 kg 0.4-0.9 mm sharp sand

Consumption: approx. 2 kg per m²/mm

CLEANING
Tools may be cleaned with water whilst the mix is still wet.

Packaging

Presentation	Bar code	Bostik code
bag - 25 kg	5412725000541	505313
plastic drum - 6 kg	5412726644669	505314