Search filter

Applications: Assembly and repair (5); Grab adhesives (5); Heating, Ventilation & Air Conditioning (13); Home decoration (35); Industrial Assembly (5); Industrial seamless floors (10); Insulating Glass (4); Labelling (15); Parquet (12); PVC welding (4); Rigid packaging (30); Sealants (7); Self-levelling compounds (14); Soft floor (carpet /PVC) (20); Substrate preparation/Primers (13); Tapes and Labels (12); Tiling (10); Wall adhesives (9); Waterproofing coatings (9); Wood working (15)
Brands: Ardal (14); Bostik (137); Eponal (14); Laybond (2); Novaflex (4); Quelyd (17); Roxol (10); Sader (13); Tarbicol (4)
Destinations: Floors (72); Walls (21)
Specific characteristics: Environmentally friendly (47); Exterior (21); Heat resistant (7); Ready-to-use (91); Suitable on wet substrate (7); Water resistant (18)
Substrates: Ceramic tiles (31); Paper/cardboard (66); PVC (25)
Segments: Construction (105); Consumer (17); Industry (95)

AGOMASTIC DECOR AG

All-purpose solvent-based grab adhesive. For all types of substrates

Additional Downloads
MSDS
Definitions
ImperviousCharacterisitc of a subfloor which porosity is very low. Adhesion on such substrates is usually more difficult and requires more attention and preparation.
Open timeTime between the moment the adhesive was applied and the moment it has no more tack (end of possible laying the covering)
Waiting timeTime between adhesive application and material bonding. It is required to wait to allow the adhesive to have enough adhesion power (tack) to receive the floor covering.

Uses

AGOMASTIC DECOR AG is a solvent-based grab adhesive used for bonding: decorative panels, profiles, battens, skirting boards, stair nosings, tiles, parquet planks, insulating panels (including polystyrene), ceiling roses and much more onto almost all types of substrates.

For interior and exterior use.

Benefits

Nail free fixing all-purpose adhesive
High filling capacity: fills gap on uneven substrates till 5 mm
Excellent bond strength onto all types of substrates: concrete, steel, wood, plasterboards, brick, glass, synthetic materials (except polyethylene)
Easy to use
Fast setting adhesive
Withstands temperatures ranging from – 20° to +80°C

Properties

Physical:

Adhesive type: sbs adhesive
Colour: cream
Viscosity: approx. 4,000 Pas
Dry solids content: approx. 81%
Specific gravity: approx. 1.35
Open time: one-way bonding – approx. 10-15 minutes; two-way bonding - approx. 15-20 minutes
Setting time: immediate bonding of fixings
Initial cure: approx 1 hour
Full cure: approx. 48 hours
Working temperature: Preferably between +10° to +30°C, not below +10°C

Safety:

IMPORTANT: before embarking on any work involving AGOMASTIC DECOR AG the separate Product Safety Data Sheet must be studied carefully by those carrying out the work. Observe good hygiene in use. Keep out of reach of children and animals. Avoid contact with eyes and skin.

Shelf life:

Up to 12 months in the original unopened cartridge, stored between +5 and +30°C.

Application

PREPARATION

Surfaces to be bonded must be clean, dry and free of grease, oil or dust. Any loose or flaking paint must be removed and lightly sanded before application.

APPLICATION

One-way method

For small and long pieces (skirting, profiles) apply on the surface a linear bead of adhesive from the cartridge using an extrusion gun.

For small panels apply by spots.

For larger pieces, apply to the surface the beads or spots of adhesive spaced 15cm apart.

Bonding should be done within 10 minutes after adhesive application.

Place the piece to be bonded into position and press firmly over entire surface to smooth the adhesive. Fixed piece can be repositioned within 4-5 minutes after bonding.

Two-way method

Bonding heavy panels or bonding onto impervious substrates (e.g. metal decking).

Follow the above-mentioned application method, but after pressing the piece into position, pull both surfaces apart. This method is used to transfer adhesive onto the substrate. Allow a waiting time of 5-10 minutes. Adjust the piece immediately into position and press firmly together. The bond is immediate.

Full cure for both application methods is of 24 to 48 hours.

REMARKS

- Work in a dust-free environment.

- Do not use on damp substrates (condensation effect)

- Do not use at a temperature below +10°C

Cleaning

Fresh and dry spillages can be cleaned with a acetone.

Packaging

Presentation	Bar code	Bostik code
Cartridge - 310 ml	3131360525104	503112