Search filter

Applications: Assembly and repair (5); Grab adhesives (5); Heating, Ventilation & Air Conditioning (13); Home decoration (35); Industrial Assembly (5); Industrial seamless floors (10); Insulating Glass (4); Labelling (15); Parquet (12); PVC welding (4); Rigid packaging (30); Sealants (7); Self-levelling compounds (14); Soft floor (carpet /PVC) (20); Substrate preparation/Primers (13); Tapes and Labels (12); Tiling (10); Wall adhesives (9); Waterproofing coatings (9); Wood working (15)
Brands: Ardal (14); Bostik (137); Eponal (14); Laybond (2); Novaflex (4); Quelyd (17); Roxol (10); Sader (13); Tarbicol (4)
Destinations: Floors (72); Walls (21)
Specific characteristics: Environmentally friendly (47); Exterior (21); Heat resistant (7); Ready-to-use (91); Suitable on wet substrate (7); Water resistant (18)
Substrates: Ceramic tiles (31); Paper/cardboard (66); PVC (25)
Segments: Construction (105); Consumer (17); Industry (95)

New Search

Print version | Download TDS

IDENDEN 10-88

Additional Downloads
6. Idenden HVAC systems (1130 Kb)
MSDS (66 Kb)
Definitions
Hot MeltAdhesive which is applied at hot temperatures and sets up while cooling
TackAdhesive power to maintain together 2 materials. Tacky surface means sticky surface.

Uses

Idenden General Purpose Adhesive 10-88 is a general purpose brushing adhesive suitable for bonding all types of thermal insulation (including expanding polystyrene) to painted and unpainted steel, aluminium and galvanised ducting.
It is also suitable for sealing overlaps of aluminium facings.
Idenden General Purpose Adhesive 10-88 is manufactured from natural rubber in a blend of solvents. It is completely toluene free.

Benefits

Excellent adhesion qualities
Strong wet tack
Suitable for expanding polystyrene
Proven over many years
Rapid drying – within 15 minutes
Wide service temperature range
Hexane free

Properties

Physical:

Colour: Light tan
Form: Liquid
Weight per litre: 0.8 kg
Composition: Natural rubber in a Hydrocarbon solvent

Typical Performance Data (approx.)

Drying time	Insulation attachment: 0-15 minutes Lap sealing: 2-10 minutes
Service temperature	-30ºC to +65ºC
Reaction to fire	Wet: Highly flammable, flash point less than +18ºC Dry: When used for its intended purpose does not detract from surface spread of flame characteristics. Class 0 compliance: Independently tested to BS 476 Part 6 – Pass and Part 7 – Class 1

Consumption:

4 square metres per litre

Safety:

Before embarking on any work involving Idenden General Purpose Adhesive 10-88, the separate Safety Data Sheet should be carefully studied by those carrying out the work.

Shelf life:

At least 12 months from date of manufacture when stored unopened in a cool, dry place within the temperature range +5ºC to +25ºC and out of direct sunlight.

Application

1. Surfaces should be clean, dry and free from dust and any loose materials. Stir adhesive thoroughly.

2. A) FIBROUS INSULATION
Apply a generous brush coating to the metal surface and press insulation firmly into place within 2-6 minutes, while the adhesive still has a strong wet tack.

B) RIGID FOAM INSULATION
Apply adhesive to both surfaces by either brush or serrated spreader. Allow solvent to evaporate for 6-12 minutes and then press insulation into place.

3. Use only in well ventilated areas and allow at least 24 hours before putting the plant into service. Do not expose to naked flame.

4. Care should be exercised when fixing rigid foam or fibrous insulation panels to ceilings and soffits by use of adhesives alone. In this situation it is recommended that panels greater than 0.5 sq. metres should be fixed into position using Idenden Insulation Hangers in addition to the adhesive.

5. Clean application equipment and remove excess adhesive immediately with white spirit.

NOTE: Idenden General Purpose Adhesive 10-88 is not suitable for bonding fibrous insulation to absorbent building surfaces (see product data sheet on Idenden Water Based Structural Adhesive 10-188).

Packaging

Presentation	Bar code	Bostik code
tin - 5 litre(s)		xxxxxx